Skip to content
LongPoint Garage Door Experts
Open 24/7(226) 641-6371Open 24/7
Gloved hands using a yellow-handled screwdriver to fasten a small black sensor to a vertical metal track beside a white door panel. — Photo-Eye Sensor Alignment or Replacement, Otterville
Person holding a multimeter and a red probe near the exposed circuit board of an overhead garage-door opener. — Garage Door Opener Diagnosis and Repair, Otterville

Openers · Otterville

Photo-Eye Sensor Alignment or Replacement in Otterville

After a cold night the door stays open until the garage warms up.

Call (226) 641-6371

In plain words

Two small sensors face each other across the doorway: one sends an infrared beam, the other receives it. While the beam lands on the receiver, the opener will close the door; the moment anything interrupts it, the door stops and returns to open. Every sensor call comes down to why the receiver has lost the beam: an object, a bent bracket, a dirty or frosted lens, sun in the receiving eye, a broken wire or a tired sensor. The technician works through those in order, fixes the one that applies, and shows you the steady indicator lights that mean the pair is talking again.

Sound familiar?

The small light on one of the sensors near the floor has gone dark, or it flickers when someone walks past the track. The other one glows steadily. The door refuses to close from the car.

How the visit goes

Photo-Eye Sensor Alignment or Replacement

How the visit goes

Paneled garage door leaning on its side against a wall, with one section on sawhorses and a tool bag on the floor. — Otterville
Technician in a cap fastening a small black plastic housing to a white frame beside a glass door, with a screwdriver. — Otterville
  1. Reading the two small lights

    Most sensor pairs carry an indicator on each side, though some older models light only the receiver, so the technician checks that model's own chart first. On most openers the sending eye shows one colour and the receiving eye another, and both should glow without a flicker. If the sending light is steady and the receiving light is dark or blinking, the beam is not landing where it should: misalignment, an obstruction or a dirty lens. If both are dark, the pair has no power, pointing up the wire to a cut, a loose terminal or reversed connections. The technician also nudges each bracket gently while watching the light; a flicker on touch means a loose mount.

  2. Bringing the pair back to the doorway

    Sometimes the sensors exist but have been defeated: taped face to face next to the head unit so the circuit is always satisfied and the door closes on anything. The technician separates the pair, checks that both still work, and mounts them where they belong on each side of the opening, low to the floor and facing each other. New wire is run down each side, brackets are fitted, and the alignment is set. The opener is then made to prove itself with the beam test, and the household is shown why the pair matters and how to keep it working, so the shortcut is never tempting again.

  3. Wiring that stays put

    The wire between the head unit and the sensors has been secured along the ceiling and walls, clipped clear of the track and, where it was exposed, run inside a protective channel. Two things keep it that way. First, when anything is fastened to those walls or that ceiling, from shelving to a bike hook to drywall, look for the thin wire before driving a screw or a staple. Second, if mice have been in the garage, a chewed wire is a common sign, so a dark sensor light after a sighting is worth a look at the run. Either way, the sensor lights will tell you the moment the circuit is open.

Photo-Eye Sensor Alignment or Replacement

In the van

  • Insulated wire staples

  • Two-conductor low-voltage wire

  • Multimeter

  • Track-mount sensor brackets

  • Protective wire channel

Technician in a black beanie fastening a hinge plate to a white door with small windows using a yellow cordless drill. — Otterville

Photo-Eye Sensor Alignment or Replacement

What affects the quote

  1. Force and travel adjustment alongside

    If the reversing turns out to involve a travel limit set long or a force setting made in summer, adjusting and re-testing those settings is included as a small extra step.

  2. Opener make and generation

    Sensor pairs are matched to the opener family, and some models take a kit with brackets and wire while others take sensors alone. The head unit label sets which pair is needed and how it is priced.

  3. Corrosion reaching the head unit

    Where salt and water have travelled up the wire to the terminals, or the sensor terminals on the board are damaged, the repair extends beyond the pair and that is set out separately.

What to have ready

  • Are there sensors at the floor on both sides, or are they missing or mounted up beside the motor?
  • How many doors and openers are there?
  • What make and model is on the opener's label, and roughly how old is it?
Call (226) 641-6371

Photo-Eye Sensor Alignment or Replacement: questions

Questions
Will the sensors need replacing or just aligning?

Most visits end in alignment, cleaning and bracket work, because the sensors themselves are hardy. Replacement comes into it when a lens has clouded or crazed, when the housing is split or holds water, an indicator stays dark with the wiring proven good, or the pair is from a different generation than the opener and is never recognised. The technician tests before choosing, so the parts list matches what the door needs.

The door closes if I hold the wall button. Is that a fix?

It is a built-in stopgap, not a repair. When the sensor circuit is not satisfied, many openers allow a close from the wall control only while the button is held, on the idea that a person standing there can see the doorway. Newer units drop that behaviour altogether and simply hold the door open. Either way the door is telling you the beam has failed, and a sensor visit puts remote closing back.

Can the sensors be mounted on the wall instead of the track?

Track-mounted clips are the preferred, manufacturer-recommended arrangement. A wall-mounted angle bracket is the next choice where the track sits far back from the opening or the clip keeps getting bumped; mounting to the concrete floor is kept as a last resort, used only when the sensor's own instructions allow it. The same rules apply: both sensors at a matched height no higher than about 15 cm, level, facing each other, with the wire secured. Wall mounting sometimes gives a cleaner beam line on older doors with unusual track layouts.

Related services

Photo-Eye Sensor Alignment or Replacement near you

Call(226) 641-6371

Request a visit

Or call (226) 641-6371 · open 24/7