Skip to content
LongPoint Garage Door Experts
Open 24/7(226) 641-6371Open 24/7
Curved galvanized steel track bending from the vertical door track into the ceiling, with perforated brackets and a recessed light. — Garage Door Track Repair or Replacement, Normandale
Gloved hand holding a white garage-door roller beside its track, with two loose rollers and a red tool on a tray. — Garage Door Roller Replacement, Normandale

Springs · Normandale

Garage Door Track Repair or Replacement in Normandale

The garage floor has settled at one corner, and the door now scrapes the concrete on that side while daylight shows at the other.

Call (226) 641-6371

In plain words

The bottom foot of a garage door track has a hard life in this climate. Slush and salt drip off the car and pool exactly where the bottom rollers sit, the jamb brackets and channel rust and thin, and a ridge of ice at the threshold can stop the door short while the opener keeps pulling. Winter track repair often means replacing the lowest section of vertical track and its brackets, sistering a jamb that has gone soft at the floor, and refixing everything into sound wood. A clear threshold and a look at the brackets each spring keep the new steel in good shape.

Sound familiar?

You bought the house with a door that sticks near the top of its travel. The vertical track was screwed tight against the jamb, so the door drags along its stop moulding on every trip instead of swinging clear.

How the visit goes

Garage Door Track Repair or Replacement

How the visit goes

Paneled garage door leaning on its side against a wall, with one section on sawhorses and a tool bag on the floor. — Normandale
Technician in a cap fastening a small black plastic housing to a white frame beside a glass door, with a screwdriver. — Normandale
  1. The horizontal run and its hangers

    Overhead, the horizontal tracks should be level with each other, or set to the same pitch, held from the ceiling by back hangs of perforated angle screwed into joists. The technician sights along each run for sag, twist or a spread channel, checks the stiffening angle riveted to the track is intact, and puts weight on each hanger to check for flex. A run that droops at the rear slopes the wrong way rather than level or its intended pitch; one knocked sideways by a ladder or stored goods twists the top section as it travels. A door drifting back toward the opening once raised points to balance instead. Any hanger anchored into drywall alone is flagged for a joist.

  2. Rollers, hinges and fixtures damaged when the door bound

    A door that has been catching on bad track usually has a few parts that suffered with it. Rollers with flat spots or bent stems are replaced, hinges that split when the door twisted are renewed, and top fixtures knocked out of line are reset so the top roller sits at the right depth. Each roller is confirmed to turn and slide freely. The channel is wiped clean of grit and old grease, and the moving parts are lubricated to the door's own manual, since track advice varies by maker. Attending to these pieces while the door is held and the track is fresh saves a second visit and stops the new alignment being chewed up by the old damage.

  3. Jamb wood that will hold a screw again

    If the visit included repairing the jamb, you now have sound timber behind every bracket, and the small habits that keep it that way are simple. Keep the bottom of the jamb dry: slush pushed clear, a bead of exterior caulk where the trim meets the slab, and paint or stain kept up on the exposed face. Look once a year for the tell-tale dark, soft patch at floor level and for screws that seem to have moved. A jamb that stays dry holds lag screws for decades, and with the track now fixed into good wood, the alignment set today has something solid to rest on.

Garage Door Track Repair or Replacement

In the van

  • Jamb brackets or continuous angle

  • Replacement rollers and hinges

  • Perforated angle back hangs

  • Vertical track, two-inch or three-inch

  • Flag brackets

Technician in a black beanie fastening a hinge plate to a white door with small windows using a yellow cordless drill. — Normandale

Garage Door Track Repair or Replacement

What affects the quote

  1. Damage to sections and bottom hardware

    When a bumper strike has also dented the bottom section or bent a bottom bracket, that repair is described and priced separately from the track so you can decide each on its own.

  2. Opener adjustment afterwards

    A door running on a freshly aligned track often needs the opener's travel limits and force reset and its reversing tested. That short adjustment is named when it is needed.

  3. Straighten or replace, piece by piece

    A dent dressed in place is labour only, while a kinked, cracked or rusted length means a new piece of track. The quote lists which pieces get which treatment.

What to have ready

  • Do you know what caused it, such as a car, a ladder or stored items?
  • Is it a single or a double door, and roughly how tall?
  • Is there one spring above the opening, or springs along the tracks?
Call (226) 641-6371

Garage Door Track Repair or Replacement: questions

Questions
How do I keep road salt from rusting the track?

Salt does its work in the bottom foot of each vertical track, where slush drips off the car and sits. Push slush clear of the door's inside edge rather than letting it pool, and on a mild day wipe or rinse the brackets and the lower channel. A little silicone spray on the bracket fasteners in autumn helps them shed water. Keeping the threshold free of ice also stops the door being pulled against a stuck bottom section.

Does a heavy insulated door need heavier track?

Usually the standard two-inch track handles a residential insulated door well, provided the gauge matches what the door maker specified and the brackets and hangers are properly fixed. Very heavy or oversized doors, and some carriage-style wood doors, are set up on three-inch track or on heavier-gauge two-inch. If a heavier door was hung on the light track from an earlier door, flexing and spreading follow, and the technician will say so.

What is the track made of, and what sizes are there?

It is galvanized steel folded into a channel that the roller wheels ride in. Residential doors almost always use two-inch track, with three-inch reserved for heavier or wider doors. The curved piece comes in a radius, commonly 12 or 15 inches, that sets how much headroom the door uses. Replacement pieces are ordered to the same profile, gauge and radius as the rest of the set.

Related services

Garage Door Track Repair or Replacement near you

Call(226) 641-6371

Request a visit

Or call (226) 641-6371 · open 24/7