Skip to content
LongPoint Garage Door Experts
Open 24/7(226) 641-6371Open 24/7
Person holding metal bars beside exposed coiled springs above a garage door. — Torsion Spring Replacement, Norfolk County
Gloved hand holding a white garage-door roller beside its track, with two loose rollers and a red tool on a tray. — Garage Door Roller Replacement, Norfolk County

Springs · Norfolk County

Torsion Spring Replacement

After pulling the red release cord, you tried lifting the door yourself and it would barely leave the floor.

Call (226) 641-6371

In plain words

A spring that breaks with the car inside puts the whole morning on hold, and this service is designed to get that door working again in a single visit. The technician arrives with a range of spring sizes, secures the door so it cannot move, identifies exactly which spring the door needs, and installs and winds the replacement. Once the door balances by hand, the opener is reconnected and tested. Until then the safe approach is simple: leave the door where it is, keep clear of it, and share a photo of the spring area so the right parts arrive on the truck.

Sound familiar?

The door starts to rise, gets about the height of your knee, then shudders and reverses. The opener sounds strained, and the top section flexes as the trolley pulls on it, because the motor is doing work the spring used to do.

How the visit goes

Torsion Spring Replacement

How the visit goes

Paneled garage door leaning on its side against a wall, with one section on sawhorses and a tool bag on the floor.
Technician in a cap fastening a small black plastic housing to a white frame beside a glass door, with a screwdriver.
  1. Following the hardware the spring drives

    The spring is one part of a chain, so the check follows that chain from the shaft outward. The centre bearing and the end bearings are turned by hand to feel for roughness or wobble. Cable drums are inspected for cracked flanges and worn grooves, and lift cables are examined along their length and at the bottom brackets, where fraying and rust usually start. Bottom brackets and their fasteners are looked at for corrosion, and the shaft is checked for straightness. Findings here decide whether the visit is a spring swap alone or a spring plus a few tired companions.

  2. Finishing the job properly

    After the balance and opener tests pass, the technician lubricates the new spring coils, bearings, hinges and roller bearings with a garage-door lubricant, leaving the track clean so the rollers run true. The old spring and any replaced parts are removed from the site. The customer is shown how the door should feel by hand, where the manual release is and how to use it, and what was installed, including the spring specification for future reference. A final look confirms clamps are off, tools are clear of the tracks and the area beneath the shaft is tidy.

  3. What cycle life means for you

    The spring you chose is rated for a number of full open-close cycles, and that number translates into years according to your routine. A standard-cycle spring on a door used four times a day works out to several years of service; a household with teenagers and a home workshop will use cycles sooner, while a high-cycle spring stretches the same routine considerably further. Knowing your rating and your habits gives you a rough sense of when the next replacement falls due, so spring service becomes a planned item like furnace maintenance rather than a surprise on a cold morning.

Torsion Spring Replacement

In the van

  • Stationary cone bolts and nuts

  • Centre bearing bracket and bearing

  • Torsion shaft and coupler

  • Socket set and wrenches

  • Wire gauge and tape measure

Technician in a black beanie fastening a hinge plate to a white door with small windows using a yellow cordless drill.

Torsion Spring Replacement

What affects the quote

  1. One spring or two

    A single-spring door needs one spring; a paired system is usually replaced as a matched set of left- and right-wound springs. The number of springs and whether both are replaced is the largest single influence on the scope.

  2. Opener reconnection and testing

    Resetting force and travel limits and running the reversal and photo-eye tests are part of the visit. An opener with worn gears or a slipping trolley uncovered during testing becomes a separate item.

  3. Shaft condition

    A bent, badly rusted or worn shaft is replaced so the drums and bearings turn true. Coupled two-piece shafts and their coupler are checked at the same time.

What to have ready

  • What is the door made of: steel, insulated steel, wood or aluminum?
  • Did you hear a loud bang before the door stopped working?
  • Can you see a gap in the spring above the door?
Call (226) 641-6371

Torsion Spring Replacement: questions

Questions
What about a garage with very little space above the door?

Low-headroom garages use a different arrangement: the spring assembly may be mounted at the rear of the horizontal tracks, or special low-headroom drums and track bring the door up with less clearance. Replacement follows the same principles, but the drums, cable routing and turn count differ. The technician identifies the system on arrival and brings hardware that suits it, so the door balances correctly in the space available.

What should I do before the technician arrives?

Keep the door closed and leave it alone, move any vehicle you can reach out of the way or at least clear the space in front of the door inside the garage, and make sure there is room for a ladder beneath the shaft. Note whether there is one spring or two and whether a cable is loose. A photo of the spring area, the drums and the opener helps the technician bring the right parts.

What other parts are often replaced with the spring?

The shaft is free during a spring change, which makes it the natural time to renew the centre bearing and end bearings if they grind or wobble. Lift cables that show fraying or rust at the bottom brackets are replaced so the new spring pulls on sound steel, and cracked or worn drums are swapped. On older doors, a corroded centre bracket or loose lag bolts may also be addressed. Each item is shown and explained before it is added.

Related services

Torsion Spring Replacement near you

Call(226) 641-6371

Request a visit

Or call (226) 641-6371 · open 24/7