Skip to content
LongPoint Garage Door Experts
Open 24/7(226) 641-6371Open 24/7
Person holding metal bars beside exposed coiled springs above a garage door. — Torsion Spring Replacement, Westmount
Gloved hand holding a white garage-door roller beside its track, with two loose rollers and a red tool on a tray. — Garage Door Roller Replacement, Westmount

Springs · Westmount

Torsion Spring Replacement in Westmount

After pulling the red release cord, you tried lifting the door yourself and it would barely leave the floor.

Call (226) 641-6371

In plain words

On a door with two springs, replacement usually starts with a conversation about scope. Both springs have completed the same number of cycles, so when one breaks the other is typically close behind, and replacing the pair together gives the door two matched springs sharing the load evenly. The technician explains what the installed system is, how each spring is loaded and what the door's weight calls for, then fits and winds the springs as a set. The result is a balanced door with a fresh cycle life on both sides rather than a repair that may be repeated soon.

Sound familiar?

On a cold morning the remote does nothing useful: the light comes on, the motor turns briefly, the door stays shut. There may be a fresh crack in a rusty coil, and flakes of orange on the floor below the shaft.

How the visit goes

Torsion Spring Replacement

How the visit goes

Paneled garage door leaning on its side against a wall, with one section on sawhorses and a tool bag on the floor. — Westmount
Technician in a cap fastening a small black plastic housing to a white frame beside a glass door, with a screwdriver. — Westmount
  1. Weighing the door honestly

    A spring is chosen for a specific load, so the technician establishes what the door actually weighs rather than guessing from its appearance. With the opener released and any remaining tension safely removed, a scale under the bottom section gives a real figure. Construction is recorded alongside it: single-skin steel, insulated steel sandwich, solid wood, glass panels or an aluminum frame all sit at very different weights for the same size. Extras count as well, including added windows, a heavy bottom seal or panels replaced over the years. That weight, with the door's height, is the basis for the spring specification.

  2. Fitting a matched pair

    On a two-spring door the springs are installed as a set: one left-wound and one right-wound, mirrored on either side of the centre bracket, with matching wire size, diameter and length so each carries half the load. Both stationary cones bolt to the centre bracket and both winding cones face outward. The technician winds each spring the same number of quarter turns, alternating between them, so the shaft is never loaded unevenly. Once both are set, the door is balanced and tested as one system. Equal springs mean equal wear, so the pair reaches the end of its life together rather than one after the other.

  3. Relief for the opener

    Your opener benefits as much as the door. With the spring carrying the weight again, the motor, gear drive, trolley and rail return to the light duty they were designed for, which tends to mean a longer working life and less noise. Force settings have been reset to suit a balanced door, so the safety reversal reacts to a genuine obstruction rather than to a heavy door. Once a year, repeat the simple reversal test by placing a length of wood flat on the floor in the door's path and confirming the door reverses on contact. The opener's photo-eye sensors deserve a wipe at the same time.

Torsion Spring Replacement

In the van

  • Stationary cone bolts and nuts

  • Centre bearing bracket and bearing

  • Torsion shaft and coupler

  • Socket set and wrenches

  • Wire gauge and tape measure

Technician in a black beanie fastening a hinge plate to a white door with small windows using a yellow cordless drill. — Westmount

Torsion Spring Replacement

What affects the quote

  1. Damage from the break

    If the opener was run against a broken spring, the top section may be bowed, the trolley bent or a hinge strained. Correcting these so the balanced door runs on straight hardware adds to the scope.

  2. Spring finish

    Oil-tempered and galvanized springs suit different garages. A coated or galvanized spring for a damp or salt-exposed space is a choice the customer can make when the specification is discussed.

  3. Converting from extension springs

    Moving a door from extension springs to a torsion system adds a shaft, bearings, drums and brackets, and removes the old pulleys, which is a broader job than replacing an existing torsion spring.

What to have ready

  • What is the door made of: steel, insulated steel, wood or aluminum?
  • About how many times a day does the door open and close?
  • Did you hear a loud bang before the door stopped working?
Call (226) 641-6371

Torsion Spring Replacement: questions

Questions
What about a garage with very little space above the door?

Low-headroom garages use a different arrangement: the spring assembly may be mounted at the rear of the horizontal tracks, or special low-headroom drums and track bring the door up with less clearance. Replacement follows the same principles, but the drums, cable routing and turn count differ. The technician identifies the system on arrival and brings hardware that suits it, so the door balances correctly in the space available.

What should I do before the technician arrives?

Keep the door closed and leave it alone, move any vehicle you can reach out of the way or at least clear the space in front of the door inside the garage, and make sure there is room for a ladder beneath the shaft. Note whether there is one spring or two and whether a cable is loose. A photo of the spring area, the drums and the opener helps the technician bring the right parts.

What other parts are often replaced with the spring?

The shaft is free during a spring change, which makes it the natural time to renew the centre bearing and end bearings if they grind or wobble. Lift cables that show fraying or rust at the bottom brackets are replaced so the new spring pulls on sound steel, and cracked or worn drums are swapped. On older doors, a corroded centre bracket or loose lag bolts may also be addressed. Each item is shown and explained before it is added.

Related services

Torsion Spring Replacement near you

Call(226) 641-6371

Request a visit

Or call (226) 641-6371 · open 24/7