Skip to content
LongPoint Garage Door Experts
Open 24/7(226) 641-6371Open 24/7
Person in a jacket facing a closed white sectional door, with coiled springs and steel tubes on a wooden bench. — Extension Spring Replacement, Westmount
Gloved hand holding a white garage-door roller beside its track, with two loose rollers and a red tool on a tray. — Garage Door Roller Replacement, Westmount

Springs · Westmount

Extension Spring Replacement in Westmount

The home inspector's report on the house you are buying flags the garage door: extension springs with no safety cable running through them, coils showing rust, and a door that sank when he lifted it partway.

Call (226) 641-6371

In plain words

A spring visit follows a fixed order, so you know what to expect. The technician releases the opener, raises the door fully and clamps it, because an extension spring is at its slackest with the door open. Then both springs, the pulleys, cables, hangers and containment cables are inspected and the door is weighed. Old springs come off, new ones go on with containment cables threaded through, cables are routed over the pulleys and both sides are hooked at the same setting. The clamps come off, the door is balanced by hand, and only then is the opener reconnected, adjusted and put through its reversal tests.

Sound familiar?

A bang like a dropped toolbox came from the garage last night. This morning one of the long springs beside the track hangs in two pieces, and the door will only rise a few inches before the opener gives up and stops.

How the visit goes

Extension Spring Replacement

How the visit goes

Paneled garage door leaning on its side against a wall, with one section on sawhorses and a tool bag on the floor. — Westmount
Technician in a cap fastening a small black plastic housing to a white frame beside a glass door, with a screwdriver. — Westmount
  1. Hangers, brackets and what they are screwed into

    Extension springs pull against whatever holds their back end, usually an angle-iron hanger bolted to the rear track support or lag-screwed into a ceiling joist. The technician checks that this anchor is tight, that the lag screws bite into wood rather than drywall or a split joist, and that the hanger has not bent under years of load. The bracket that carries the fixed pulley at the front of the track is checked the same way, along with the bottom brackets on the door that the lift cables pull on. An anchor that has loosened lets the spring's geometry drift, which is one reason a door slowly becomes uneven.

  2. Running the lift cables

    Each lift cable starts at the bottom bracket, where its loop goes over the pin or is secured with a clevis pin. From there it runs up the vertical track, over the fixed pulley at the front of the horizontal track, back along the track to the pulley on the end of the spring, around it, and forward again to the S-hook or adjusting clip at the front hanger. The technician keeps the cable seated in each pulley groove and makes sure it passes on the correct side of the containment cable and the track. Cables are renewed if the old ones showed any fraying or rust, and always as a pair of the same length.

  3. The numbers that stay with the door

    Before leaving, the technician tells you what the door weighed, which spring rating and length went on, whether the pulleys and cables were renewed, and which hook position the cables were set to. Write it on a card by the opener or inside the door's manual. Extension springs are sold by rating and length, so the next set can be ordered from that card without weighing the door again, and a technician arriving later can see at a glance whether the door has been altered since. Add the date and roughly how many times a day the door is used; together those two facts give a fair idea of when the springs will be due again.

Extension Spring Replacement

In the van

  • Lift cables

  • S-hooks and adjusting clips

  • Door-weighing scale

  • Garage-door spray lubricant

  • Containment (safety) cables

Technician in a black beanie fastening a hinge plate to a white door with small windows using a yellow cordless drill. — Westmount

Extension Spring Replacement

What affects the quote

  1. Corroded fasteners

    In an unheated garage the bolts through pulley forks and hanger brackets rust solid; freeing or cutting them and fitting new hardware takes time and shows in the parts list.

  2. Door weight and size

    Spring rating follows the door's weight, and a wide insulated door or a wood door takes heavier springs than a light single. Weight and height together set the parts on the quote.

  3. Condition of the lift cables

    Cables with fraying, rust at the loop or a kink are renewed as a pair while the springs are off. Sound cables are re-routed and set, and the quote says which applies.

What to have ready

  • Is it a single or a double door, and what is it made of?
  • Do you know how old the springs are or when they were last changed?
  • Does the door drop the last bit, or drift up on its own?
Call (226) 641-6371

Extension Spring Replacement: questions

Questions
What if the spring hanger has pulled loose from the ceiling?

It is put right as part of the job. The rear hanger takes the full pull of the spring on every cycle, and lag screws driven into thin plywood, a split joist or drywall work loose over the years, which is often why a door slowly goes out of balance. The technician re-fixes the hanger with fresh lag screws into solid framing, or adds a length of angle iron to reach it, before the new springs are hung.

Why does the opener get adjusted after new springs?

Because the door is now much lighter for the opener to move. Over the years, as the old springs weakened, the opener's force setting may have been turned up to keep the door going, and its travel limits were set against a door that sat differently on the floor. Left alone, that extra force would push the newly balanced door too hard. Resetting force and travel, then repeating the reversal tests, matches the opener to the door it now has.

The door creeps open on its own. Is that a spring problem?

Usually, yes. A door that rises from the floor or from halfway without help has springs pulling harder than the door weighs, which happens when a heavier-rated pair was fitted, when the hooks were set with too much stretch, or when a door has been made lighter by a panel change. It also puts strain on the opener, which has to hold the door down. Weighing the door and fitting the correct rating, set evenly, settles it.

Related services

Extension Spring Replacement near you

Call(226) 641-6371

Request a visit

Or call (226) 641-6371 · open 24/7